Swingarm

* Special Order DEPOSIT

Use this Deposit to secure your order when a part has gone out of stock or is a custom request LOG IN or CREATE AN ACCOUNT ADD TO CART the Special Order Deposit CLICK PROCEED TO CHECKOUT SCROLL...

30510143 Nut M7x1 Zinc (h. 5.0mm)

M7x1 Nut Zinc Plated

30510143.1 Nut M7x1 Zinc (Special h. 7mm)

Special Nut M7x1 with Extra Height 7mm, spanner size 11mm

31210340 Tie Rod Steel 218mm-M10

Brake Caliper Tie Rod. For use with 1 x Tie Rod End M10 and 1 x Clevis M10 for SFC1000 when fitted with Wire Spoked Wheels.

31210340.1 Tie Rod Steel 284mm-M10

Brake Caliper Tie Rod. Extra long to use with 2 x  Tie Rod End M10 for SFC1000 when fitted with Cast Wheels.

31310101 see 31310112 Chain Adjuster SS

This part number has been superseded by 31310112 Chain Adjuster 17mm

46101022 Rod End M10x1.5 SA10E chrome steel race

Zinc Plated High Tensile SAE10 E High Load Rod End. Specifically extra strong for brake stays and other applications where strength and reliability is required. Inexpensive nylon type rod ends are...

Brake Caliper Link Rod Zane Laverda

BREMBO Brake Caliper Support BREMBO REAR Laverda 650/668

BRAKE CALIPER SUPPORT FITTED TO LAVERDA 650/668 MODELS  

Chain Adjuster 17-18mm with 6mm bolt (2/SET) CHROME

Chrome Chain Adjuster with M6 adjusting bolt and 18mm Hole. Suits 17 and 18mm Axles.

Chain Adjuster 17-18mm with 7mm bolt STAINLESS

Stainless steel Chain Adjuster for the left-hand side drum-brake wheel and either side for disc brake models. Axle Diameter ø17mm. Part 31310101 and 31310112 are the same part.

Chain Adjuster Right Side 25mm STAINLESS (Laverda Drum Brake)

Stainless steel Chain Adjuster for the right hand side drum-brake chain carrier. Diameter ø25mm

Chain Slider Rubber (Laverda SFC1000)

Final Drive Chain Slider/Protection for alloy swingarm fitted to Laverda SFC1000

Silentbloc Bush (50210980)

Measures ID Ø14mm. Laverda part for 350/500 models swingarm bush and also for the fairing support on SFC750, RGS and other models.

Swingarm Bearing Grease Nipple 90º M10x1

Note: the grease nipple for the Laverda swingarm pivot requires the length of 6mm or less to avoid contact with the internal Bearing Distance Spacer.

Swingarm Bearing Sealing Washer (Acetel) (2/SET)

Special washer manufactured in acetel for sealing the Laverda swing-arm pivot bearing. Acetal (polyoxymethylene) is a lightweight and low-friction polymer commonly known as Delrin (DuPont’s brand...

Swingarm Bearing SET for 14mm spindle (Laverda 500/750/1000/1200/RGS/SFC1000) *conversion from bushes requires additional spacer

Swingarm Needle Roller Bearing Kit for Laverda motorcycles with 14mm spindles. This kit is used to upgrade from the Swingarm Bush 21510310 and converts the swingarm pivot to Needle Roller. To...

Swingarm Bearing SET for 16mm spindle (Laverda SFC)

Swingarm Needle Roller Bearing Kit for Laverda models with 16mm spindles. Bearing 22 805 523 Bush     21 601 107 Washer 33 116 340  

Swingarm Bearing Spacer Laverda 1200 frame models (and 500, 750, 1000 with needle roller conversion)

Bearing Spacer for the Laverda 1200 frame swingarm. Some late model Laverda 1000 were built with 1200 frames that have needle roller bearing in the swingarm. Also required when converting 500, 750...

Swingarm Bearing Spacer Laverda 500/750GT/SF13